Toluene diisocyanate manufacturer Knowledge Ethylbenzene Ethylbenzene

Ethylbenzene Ethylbenzene

Ethylbenzene Structural Formula

Structural formula

Business number 02HU
Molecular formula C8H10
Molecular weight 106.17
label

Ethylbenzene,

phenylethane,

Phenethane,

Aethylbenzol,

Phenylethane,

Nitro spray paint thinner,

organic synthesis solvents,

cellulose ether solvent,

For synthesis of synmycin,

Aromatic hydrocarbons

Numbering system

CAS number:100-41-4

MDL number:MFCD00011647

EINECS number:202-849-4

RTECS number:DA0700000

BRN number:1901871

PubChem number:24889462

Physical property data

1. Properties: Colorless and transparent liquid with aromatic odor. [1]

2. Melting point (℃): -94.9[2]

3. Boiling point (℃): 136.2[3]

4. Relative density (water=1): 0.87 (20℃)[4]

5. Relative vapor density (air = 1): 3.66[5]

6. Saturated vapor pressure (kPa): 0.9 (20℃)[6]

7. Heat of combustion (kJ/mol): -4390.1[7]

8. Critical temperature (℃): 344.1[8]

9. Critical pressure (MPa): 3.60[9]

10. Octanol/water partition coefficient: 3.15[10]

11. Flash point (℃): 12.8 (CC) [11]

12. Introduction Ignition temperature (℃): 432[12]

13. Explosion limit (%): 6.7[13]

14. Lower explosion limit (%): 1.0[14]

15. Solubility: Insoluble in water, miscible in most organic solvents such as ethanol, ether, and benzene. [15]

16. Viscosity (mPa·s, 25ºC): 0.6354

17. Heat of evaporation (KJ/mol, 25ºC): 42.278

18. Heat of fusion (KJ/mol, -94.975ºC, 101.3kPa): 9.190

19. Heat of formation (KJ/mol, 25ºC, gas): 29.810

20. Heat of formation (KJ/mol, 25ºC, liquid): -12.464

21. Heat of combustion (KJ/mol, 25ºC, gas): 4610.21 (H2O liquid): 4389.98

22. Heat of combustion (KJ/mol, 25ºC, liquid): 4567.92: 4347.69 (CO2 gas)

23. Specific heat capacity (KJ/(kg·K), 298.16K): 1.21

24. Solubility (%, 25ºC, water): 0.0152

25. Volume expansion coefficient (K-1, 0~40ºC): 0.00056

p>

26. Critical density (g·cm-3): 0.284

27. Critical volume (cm3·mol-1): 374

28.. Critical compression factor: 0.2643

29. Eccentricity factor: 0.304

30. Solubility parameter (J·cm-3)0.5:18.043

31. van der Waals area (cm2·mol-1): 8.800×109

32. van der Waals volume (cm3·mol– 1): 69.740

33. Gas phase standard combustion heat (enthalpy) (kJ·mol-1): -4607.13

34. Gas phase standard claims heat (enthalpy) (kJ·mol-1): 29.92

h2 id=”hc”>Synthesis method

4. The liquid phase alkylation method is usually At normal pressure and 85-90°C, aluminum trichloride is used as a catalyst to react ethylene and benzene to produce ethylbenzene. A side reaction is that ethylbenzene is further alkylated with ethylene to form polyethylbenzene. Industrially, the benzene conversion rate is limited to 52-55%, and a high benzene-ethylene molar ratio (generally around 2) is used to prevent the formation of more diethylbenzene and polyethylbenzene. The average yield of ethylbenzene is 94-96%.

5. The gas-phase alkylation method initially involves gas-phase alkylation of ethylene and excess benzene under the action of phosphoric acid-diatomite on alumina-silica gel catalyst at 300°C and 4-6 MPa. Ethylbenzene is produced through sylation reaction. Since the catalyst used cannot dealkylate polyethylbenzene, polyethylbenzene cannot be treated. Although the production of polyethylbenzene is reduced by increasing the benzene batching ratio, it increases the distillation cost of recycled benzene.

6. Separation of C8 aromatic hydrocarbons to produce ethylbenzene and aromatic hydrocarbons produced by catalytic reforming. After benzene and toluene are separated and removed, the boiling points of the components of the mixed xylene fraction are very close. It takes 300-400 trays to separate ethylbenzene by distillation, and the reflux ratio is 75. In addition, adsorption separation and chromatography can also be used to resolve ethylbenzene. Since the separation of ethylbenzene from C8 aromatics is no longer economically competitive with benzene alkylation of ethylbenzene, and a new generation of precious metal isomerization catalysts can effectively convert ethylbenzene into xylene, the importance of ethylbenzene separation has greatly increased. decline.

Purpose

1. The main use is to produce styrene through dehydrogenation. Others are used as intermediates of synmycin in medicine. Also used as diluent for nitrocellulose spray paint and solvent for organic synthesis. It becomes a good solvent for cellulose ethers when mixed with ethanol and ethyl acetate.

2. Used in organic synthesis and as solvent. [31]

This article is from the Internet, does not represent the position of Toluene diisocyanate reproduced please specify the source.https://www.chemicalchem.com/archives/23473

author:

Previous article
Next article
Contact Us

Contact us

+86 - 152 2121 6908

Online consultation: QQ交谈

E-mail: sales@newtopchem.com

Working hours: Monday to Friday, 9:00-17:30, closed on holidays
Follow wechat
Scan wechat and follow us

Scan wechat and follow us

Follow Weibo
Back to top
Home
E-mail
Products
Search